how to fix ford 6.0 diesel problems

How To Fix Ford 6.0 Diesel Problems? HPOPs probably last a few hundred thousand and cost a couple grand to replace. The bottom end should go 500k to a million miles, and given how long they last, used ones are kind of cheap if you need one. I’ve read about high mileage 6.0s that still have nice cylinder bores.

What is the life expectancy of a Ford 6.0 diesel engine? HPOPs probably last a few hundred thousand and cost a couple grand to replace. The bottom end should go 500k to a million miles, and given how long they last, used ones are kind of cheap if you need one. I’ve read about high mileage 6.0s that still have nice cylinder bores.

Why is the 6.0 Powerstroke unreliable? The 6.0L Power Stroke fuel injection system operates on oil pressure, very high oil pressure. Problems with the HPOS are oil leaks (internal to the engine) due to failed/deteriorated O-rings that are caused by excessive oil temperatures (bad oil cooler) and high pressure.

Is Ford 6.0 diesel a good engine?

The 6.0L is a good engine when it is running properly. It has one main failure that is commonly overlooked and is the cause of most of the big issues this engine has. The oil is the life blood of the 6.0L diesel as the injectors are hydraulically actuated using engine oil to drive them.

What powerstroke to avoid?

What Years Are Ford Diesel Engines To Avoid? This Ford Super Duty six came out between 2003 and 2007. As far as diesel trucks go, 0L can be said to be the most horrendous. Powerstrokes with 0L capacity are notorious.

What is needed to BulletProof a 6.0 Powerstroke?

The fine folks at BulletProof Diesel define 6.0L Power Stroke as being “bulletproofed” when it has at least four of the five main problem areas addressed. These five areas are: Oil cooler, EGR cooler, head studs, fuel injection control module (FICM), and water pump.

How many miles can a bulletproof 6.0 go?

But they will give you a solid 50,000-80,000 miles, especially with proper fluid changes. A Ford oil cooler is ~$300 and labor at 10 hours is ~$800. Needless to say, you can do a lot of Ford oil cooler changes for one Bulletproof oil cooler.

How long do 6.0 injectors last?

With proper care and maintenance of the engine, you can expect a diesel injector to last between 200,000 and 300,000 kilometres.

Is 6.0 or 7.3 Powerstroke better?

From a reliability, durability or simplicity standpoint, the 7.3L is hands down the winner. When it comes to horsepower, drivability and meeting modern day emissions standards, the 6.0L has it beat. Ultimately, both engines have their pros and cons.

How much does it cost to replace a 6.0 diesel engine?

On average, the cost of a 6.0 powerstroke diesel engine rebuild is going to be around $7,500. Or, if you choose to get this engine rebuilt from a parts kit, a parts kit will cost you about $2,165 on average.

What years are Ford diesel engines to avoid?

Ford SuperDuty Diesel Truck Problems: Fixing Them From 2003-2007. In my experience, most diesel lovers avoid buying the 2003 to 2007 model-year Ford Superduty diesel trucks. The 6. Powerstroke 0L produces problematic power when used in large quantities.

How hot is too hot for 6.0 Powerstroke?

It is really too hot for continuous service when the temperature is over 220*F – most likely something is not right when the temperature is constantly above that level. For more than 30 minutes, keep the temperature below 250*F.

When should I plug in my 6.0 Powerstroke?

A general rule of thumb is to plug in your engine block heater when the weather reaches -15° C or lower, just to be safe. If you drive a diesel vehicle, you may need to plug in the engine block heater before temperatures drop that low.

Which Ford Powerstroke engine is the best?

#2 – 6.7L Power Stroke – (Best Ford Diesel Engine) Ford’s 6.7L diesel served as the first engine of Power Stroke lineage not to be produced by International Navistar.

How much horsepower can a stock 6.0 Powerstroke handle?

Even a decade ago, before PCM tuning was anywhere near as refined as it is now, several 6.0L owners proved the 6.0L’s bottom end could withstand 700-rwhp. Today, a lot of serious enthusiasts conclude that the 800 hp 6.0 Power Stroke range gets you into unchartered waters with a 6.0L.

What is Ford’s most reliable diesel engine?

The 7. As the most reliable engine, the 3 liter Powerstroke is easy to operate when it isn’t filtered to prevent emissions. As a result, the reliability of the 7 has been enhanced. Powerstrokes with 3 liter fuel are sometimes found in pickups such as the 2000 Ford F-250.

What year powerstroke is best?

In terms of Ford Super Duty trucks, models 2012 and any models since 2013 or newer, as well as 2017 models, have the best value, but 2017 versions had a couple of problems… In light of the 2008-10, 2009, 2010, and 2011 Ford Super Duty trucks, you will need to stay out of them.

How much does it cost to bulletproof an engine?

However, most engines these days are powerful enough to handle heavy shielding. Depending upon the choice, the bulletproof coating of the engine can roughly cost you, ranging from $5,000 to $10,000.

How much is a bulletproof 6.0 worth?

Install can run about $700-1,000 so the upgrade can cost upwards or beyond $3,000 all in. Compare that to a factory Ford 6.0 Power Stroke oil cooler for about $300. Add in labor and you can still replace the factory oil cooler about 3x before the bulletproof 6.0L oil cooler upgrade is worth the cost.

What does deleted mean on a diesel truck?

Deleting a truck means removing or bypassing the diesel particle filter, the exhaust regulating system, and diesel emission fluids. Deleting a truck increased fuel efficiency by 20 – 30% while also making it more powerful and requiring less maintenance cost.

How long will a powerstroke last?

In addition to Duramax and Cummins engines, Powerstroke engines are found in Ford trucks. They can generally last 500,000 miles per year. In general, Powerstroke engines are classified as having between 350,000 and 500,000 miles of warranty.

What causes injector failure in 6.0 Powerstroke?

Another common cause of injector failure in the 6.0L is fuel interruption and/or air in the fuel system, where the fuel filters or fuel lines get clogged so the injectors can’t fill up with fuel between cycles.

Trafficautodriving Scroll to Top